Leave Your Message
Compact Wave Springs from China - Leading Suppliers & Factory for Customized Solutions in Tight Spaces
Hot Products

Compact Wave Springs from China - Leading Suppliers & Factory for Customized Solutions in Tight Spaces

Wave Springs are innovative solutions designed to replace traditional round wire Compression Springs in applications with stringent load deflection specifications, particularly in space-constrained environments. As a leading supplier in China, SMS Spring offers a comprehensive range of both standard wave spring series and customized wave springs tailored to meet your specific needs. Our factory specializes in manufacturing high-quality custom wave springs, ensuring that we can deliver optimal performance for your applications. Choose SMS Spring for reliable wave springs that adhere to the highest industry standards

    Information

    A wave spring is essentially a compression spring made of coiled flat wire with waves added along the coils to give it a spring effect. Wave springs are manufactured with either a plain end design, commonly known as wavy ends; or squared-flat end design, also known as a shim end.

    Wave Springs – Compact size for the tight space application (2)

    Helpful Wave Spring Tips

    Wave Springs – Compact size for the tight space application (3)
    • Avoid operating beyond the listed Nominal Load and Working Height, or the stresses may cause permanent spring set or failure.
    • Solid Height information is provided for reference only. Operating to solid will cause extreme overstress regardless of the actual load or size of a wave spring design.

    Applications

    Wave springs are found in a wide variety of applications where structural considerations restrict the installation height, where uniform force distribution is needed and/or uniform rotational pressure is required over 360°. Wave springs are suitable for both static and slightly dynamic load applications, however, fatigue is a critical consideration when designing a wave spring for dynamic load applications. For higher life cycles a stronger wave spring is needed. Special solutions must be found for extremely dynamic applications, since considerable stress on the side wave curves can cause material abrasion at the contact point. Typical applications include connectors, clutches, valves, pumps, seals, medical equipment etc.

    Wave Spring Materials

    SMS Spring’s Wave Springs are manufactured from a single filament of Type 17-7 Stainless Steel flat wire formed in continuous precise coils with uniform diameters and waves. For custom designs, there are many material and finish options. For high temperature and corrosive environments, careful material selection is required. You can consult with a SMS Spring engineer for technical information.

    Stock Wave Springs

    SMS Spring offers standard wave springs in both imperial and metric sizes:

    • Imperial: Diameters available from .250” (6.35 mm) to 1.75” (44.45 mm) to meet load requirements from 2 lbs (8.9 N) to 90 lbs (400.3 N)
    • Metric: Diameters available from 6 mm (.236 in) to 45 mm (1.772 in) to meet load requirements from 6 N (1.35 lbs) to 400 N (89.9 lbs)

    Wave Springs Specifications

    Material Stainless Steel Type 17-7 PH
    Wire Type Single strand of pre-tempered flat wire
    Max Temperature 650° F (340° C)
    Finish Passivated
    Coils Continuous Coil
    Design Uniform diameter and wave heights

    Custom Wave Springs

    Custom wave springs can be manufactured with a wide range of material, finish and size options to meet your exact design specifications. You may work with a SMS Spring Engineer to assist with the design and technical details for using a custom wave spring in your application. SMS Spring offers custom springs in both small and long run quantities.

    Design Considerations

    There are 4 critical factors when considering a wave spring:

    1. Constraints of the application: Bore/shaft, ID/OD etc.
    2. Load requirements
    3. Working height at which the load is applied
    4. Material desired
    Static Applications: Make sure the % stress at working height is less than 100%. The spring will take a set if subjected to a higher stress.
    Dynamic Applications: Make sure the % stress at working height is less than 80%. A wave spring will take a set if subjected to a higher stress.

    Precautions

    • If the working height of a wave spring per turn is less than (2 * Wire Thickness), the wave spring will operate in a 'non-linear' range and actual loads may be higher than calculated.
    • Number of turns must be between 2 and 20.
    • Number of wave per turn (N) must be ½ increments.
    • Min. Radial wall = (3 * Wire Thickness).
    • Max. Radial wall = (10 * Wire Thickness).
    • It is NOT recommended to compress a wave spring to solid height.
    • Outside diameter (OD) expansion and outside diameter (OD) tolerance must be taken into account while designing a spring to fit in a bore and/or over a shaft.
    Wave Springs – Compact size for the tight space application (1)

    Frequently Asked Questions

    What is the structural advantage of using a wave spring?
    Wave springs are ideal for tight-space applications where structural limitations restrict installation height while requiring uniform 360° force distribution and rotational pressure.
    What end designs are standard for wave springs?
    Wave springs are manufactured with either a plain end design (commonly referred to as wavy ends) or a squared-flat end design (also known as a shim end).
    Why should wave springs not be compressed to solid height?
    Operating to solid height causes extreme overstress regardless of the load or size design, leading to permanent spring set or premature spring failure. Solid height is provided for reference only.
    What are the stress limits for static vs dynamic applications?
    For static applications, stress at working height should remain below 100%. For dynamic applications, stress should be kept below 80% to prevent setting and fatigue issues.
    What standard material is used for SMS Spring stock wave springs?
    Stock wave springs are produced using single strands of pre-tempered Stainless Steel Type 17-7 PH with a passivated finish, capable of handling operating temperatures up to 650°F (340°C).
    Can wave springs be customized for custom load and bore requirements?
    Yes, custom wave springs can be configured with specific diameters, materials, finishes, and turns for both low-volume prototype and high-volume production runs.